Happisland Drill Bits for 3D Printer Nozzle Cleaning Kit Pack of 7 PCS: 0.2mm 0.25mm 0.3mm 0.35mm 0.4mm 0.45mm 0.5mm

Pack of 7 PCS: 0.2mm 0.25mm 0.3mm 0.35mm 0.35mm 0.4mm 0.45mm 0.5mm

Product Features

  • Pack of 7 PCS: 0.2mm 0.25mm 0.3mm 0.35mm 0.35mm 0.4mm 0.45mm 0.5mm
  • Conveniently colored silicone grip gasket for spinning bits by hand
  • Color is random
  • Note:Don’t use the drill to clean until the nozzle is heated to above 200 degrees
  • Any question,pls feel free to contact us.

Click Here If You Need More Detailed Info…

Professional 3D printer CNC Kit for arduino, Kuman GRBL CNC Shield +UNO R3 Board + RAMPS 1.4 Mechanical Switch Endstop + DRV8825 A4988 GRBL Stepper Motor Driver with heat sink + Nema 17 Stepper Motor

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware)

Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles
Length of Cable: 70 cm

Package Contents:
1 x CNC Shield Board
1 x Kuman UNO R3 Board 
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
12x M3 Screws for bracket of stepper motor
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
1 x 1.5m USB cable for R3 Board

Product Features

  • Latest CH340G CNC Shield expansion board Version 3.0 for Arduino
  • Kuman UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable
  • 4pcs DRV8825 Stepper Motor Driver with heat sinks
  • 3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws
  • 3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable

Click Here If You Need More Detailed Info…

HICTOP CR-10 3D Printer Prusa I3 DIY Kit Aluminum Large Print Size 300x300x400mm


Product Specifications:
Extruder quantity: 1
Molding: FDM
Body Structure: Imported V-Slot Aluminum Bearings
Nozzle Diameter:Standard 0.4mm
Printing Method: SD card(off-line), contact to the PC(online)
LCD screen: 3 inch LCD screen with aircraft knob
Power supply: input: 110-240V output: 12V
Hot bed: Industrial grade aluminum alloy platform, 3mm special tempered glass
Operating Software:CURA、Repetier-Host simplify 3D
Software supporting: PROE, Solid-works, UG, 3d Max, Rhino 3D design software, etc.
Cura language: English
Interface language: English
Format : STL, G-Code
Operating System: Linux, Windows, OSX

Product Parameter:
Printing Size: 300*300*400mm
Printing accuracy:±0.1mm
Layer thickness: 0.05-0.4mm (adjustable)
Nozzle temp: 250 degree
Extruder temperature: PLA: 210
Hot bed temperature: PLA: 50
Printing Speed:Normal: 80mm/s, Max.: 200mm/s
Materials:1.75mm PLA

Packing details:
Product Size: 490*600*615mm
Package Size: 540*640*310 mm
Net Weight: 10.3kg
Gross Weight: 14kg
Working condition temp: 10-30℃, Humidity:20-50%

Package content:
a. HICTOP 3D printer DIY kits (including build plate and tempered glass)
b. Spare screws and Wrench kits
c. Assembly instructions and user manual.
d. SD card*1
e. 0.2kg PLA Filament

Product Features

  • EASY ASSEMBLY: Delivery with three sets, just need about 10 minutes to assemble well.
  • PRINTING SIZE: Prints max size of 300X300X400mm. No longer will you be limited to small models.
  • LONG SERVICE LIFE: Imported Linear navigation with low friction. Industrial-grade PCB can continuously print for 200 hours without pressure
  • HEATING BED: Industrial grade aluminum alloy platform&special tempered glass to ensure the formation of flat and to prevent wear and tear. Easy to take out the model.
  • EASY WIRING: Wires are already connected to the control board & cables are also attached,easy for wiring.

Click Here If You Need More Detailed Info…

3D Pop Up Handmade Cards Creative Greeting Cards Paper craft (Red Roses)

We’ll always feel something is missing when we send gifts without greeting cards, express your feeling by words, the greeting card will be the carrier of your words, if this carrier in three-dimensional, there will be more surprises. if you want to gift surprises, then try this Pop-Up 3D Greeting Cards The handmade card is more than a greeting card, The one who opens it will be pleasantly surprised by this unique gift, will be touched in their mind .

Product Features

  • Size: 15cm x 15cm (Folded)
  • Material:Card paper / Features:Pop-up Cards
  • Notice:Please open Gently.May be snapped if pull too hard.
  • Suitable for: Invitations / Birthday cards / Sorry / Christmas cards / Thank you cards / Mothers day cards / Wedding invitations

Click Here If You Need More Detailed Info…

Happisland Drill Bits for 3D Printer Nozzle Cleaning Kit Pack of 10PCS: 0.3mm 0.4mm 0.5mm 0.6mm 0.7mm 0.8mm 0.9mm 1.0mm 1.1mm 1.2mm

10 Pcs Drill Bits:0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1.0, 1.1, 1.2mm

Product Features

  • Pack of 10 PCS: 0.3mm 0.4mm 0.5mm 0.6mm 0.7mm 0.8mm 0.9mm 1.0mm 1.1mm 1.2mm
  • Conveniently colored silicone grip gasket for spinning bits by hand
  • Color is random
  • Note:Don’t use the drill to clean until the nozzle is heated to above 200 degrees
  • Any question,pls feel free to contact us.

Click Here If You Need More Detailed Info…

Tarantula i3 3D Printer Kit / SD-Card Reader / USB 2.0 & 2 Rolls Filament Bundle

Whatsapp: +90 507 980 02 84 Skype: mutemancer The Aluminum Print Bed plate is 200mm X 200X 200mm – the travel for the build plate is limited by the physical dimensions of the frame itself and that is around 220 mm for the X-axis (side to side), 260-270mm for the Y-axis (front to back) and around 200mm for the Z-Axis (up and down). Model – Complete DIY Kit (Unassembled). Less parts. Easy Assembling. High performance. Better than reprap prusa i3. T echnical Specifications: Layer resolution of 50 microns. MAX Printing Speed: 150 mm/s. Build size: 200X 200 X 200mm. Full Metal E3D Bowden long distance Extruder. Material type: PLA, ABS, PETG, Wood, PVA and Flexible Filaments (With Pro Metal Extruder). Material specifications 1.75mm in diameter. Positioning accuracy: Z 0.004mm, XY 0.012mm. Printing Color: Single color. Nozzle diameter: 0.4mm (customized 0.3mm/0.2mm). Recommended extruder temperature: 210°C (the maximum can be set to 260°C). Heating plate temperature: 60-120°C (proper winter warming and summer appropriate cooling). Best ambient temperature: ≥25°C. Power requirements: 220V, 250W, 50Hz, 0.89A. Connection: TF card or USB. The file print format: STL,G-Code. Compatibility: Windows, Linux, Mac. CE, FCC specifications: CE, FC, ROHS. Device weight: 7.5kg. Equipment size: 430 X 440 X400mm. Package size: 440X 340X 190mm

Product Features

  • SHIPPING AFTER 10. FEB !

Click Here If You Need More Detailed Info…

LI YU SZ Upgraded DIY Desktop 3D Printer – Prusa i3 Kit, High Accuracy Self-Assembly Tridimensional FDM Printer with Free Rolls Filament Gift

Package Included:

Auto leveling Standard
All assembly units
All assembly tools
All assembly datasheet (document, picture)
Software
8G SD Card
1 x Masking paper
Free 1 Rolls Filaments
Filaments color : Random color, PLA or ABS net weight 0.25kg/roll

Feature:

Structure: Acrylic Framework
Power Shupply: 110/220V 20A
Output: 12V 20A 240W
Off-line Print: Support
XY Axis speed : 3000mm/min
Printing Speed: 40-120mm/s
Layer Thickness :0.1mm~0.4mm
LED Screen: support
Z Axis speed:200mm/min
Hotbed Temp: 110
Extruder Temp: 170~275
Printing Size: 220x220x240mm
Filament Diameter: 1.75mm
Machine Size: 500x400x230mm
XY Axis Accuracy: 0.012mm
Z Axis Accurancy: 0.004mm
Nozzle size : 0.4mm

Note: all 3D Printer assembly video are in free SD card, if you have any problem within install please contact us at any time.

Product Features

  • Self-leveling, self-cleaning, tetherless printing, and an integrated power supply make powerful 3D printing easy
  • A large build volume of 220 mm x 220 mm x 240 mm enables large prints, or many small prints at once
  • High accuracy printing Operating to easy Support auto level ans off-line print
  • SUPPORT SEVERAL FILAMENTS: Prints PLA and higher temperature ABS, TPU,WOOD,PVA, Nylon,PVA and PP. Print many filaments and not just PLA.

Click Here If You Need More Detailed Info…