Nema 14 Bipolar Stepper Motor 5.4V 0.8A 25.5oz.in/18Ncm 3D Printer

This hybrid bipolar Nema 14 stepper motor with 1.8 deg. step angle (200 steps/revolution).
Each phase draws 800 mA at 5.4 V, allowing for a holding torque of 18Ncm(25.5oz.in).

Electrical Specification:

* Manufacturer Part Number: 14HS13-0804S
* Motor Type: Bipolar Stepper
* Step Angle: 1.8 deg.
* Holding Torque: 18Ncm(25.5oz.in)
* Rated Current/phase: 0.8A
* Phase Resistance: 6.8ohms
* Inductance: 10mH+/-20%(1KHz)

Physical Specification:

* Frame Size: 35 x 35mm
* Body Length: 34mm
* Shaft Diameter: 5mm
* Shaft Length: 24mm
* D-cut Length: 16.5mm
* Number of Leads: 4
* Lead Length: 400mm
* Weight: 190g

Connection:

Black(A+), Green(A-), Red(B+), Blue(B-)

Warning:

Make sure the motor connect to a constant current or chopper drive controller before you test motor.
Connecting the motor directly to a power supply will destroy the motor.

Product Features

  • Middle Size with Hight Torque
  • 18Ncm(25.5oz.in) holding torque
  • NEMA 14 bipolar 1.38″x1.38″x1.34″ 4-wir
  • 1.8 deg. step angle(200 steps/rev)
  • Rated current 0.8A & resistance 6.8ohms

Visit The Website For More Information…

Professional 3D printer CNC Kit for arduino, Kuman GRBL CNC Shield +UNO R3 Board + RAMPS 1.4 Mechanical Switch Endstop + DRV8825 A4988 GRBL Stepper Motor Driver with heat sink + Nema 17 Stepper Motor

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware)

Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles
Length of Cable: 70 cm

Package Contents:
1 x CNC Shield Board
1 x Kuman UNO R3 Board 
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
12x M3 Screws for bracket of stepper motor
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
1 x 1.5m USB cable for R3 Board

Product Features

  • Latest CH340G CNC Shield expansion board Version 3.0 for Arduino
  • Kuman UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable
  • 4pcs DRV8825 Stepper Motor Driver with heat sinks
  • 3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws
  • 3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable

Click Here If You Need More Detailed Info…

Longruner 3d Printer Controller Kit Mega 2560 R3 + Ramps 1.4 + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display Controller with Adapter for Arduino Reprap

Update High Quality Ramp Board by changing MOSFET: Old MOSFET IC Model : PDF55N06 Specification:VDSS:60V ID:55A New MOSFET IC model: HM60N06 Specification:VDSS:60V ID:60A HM60N06 current up to 60A, More safety Package List: (1) RAMPS 1.4 x 1 (2) Kuman Mega 2560 R3 x 1 (3) A4988 Stepper Motor Driver with Heatsink x 5 (4) LCD 12864 Graphic Smart Display Controller x 1 (5) Smart Adapter x 1 (6) Cable x 2 (7) USB Cable x 1

Product Features

  • 2017 Updated Version 3D Printer Controller RAMPS 1.4 It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • Mega 2560 compatible with arduino.
  • LCD 12864 Graphic Smart Display Controller This full graphic Smart Controller contains a SD-Card.
  • A4988 Stepper Motor Driver A4988 is a complete microstepping motor driver with built-in translator for easy operation.
  • Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents.

Click Here If You Need More Detailed Info…

Quimat 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits +RAMPS 1.4 + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap

Package Content: (1) Mega 2560 (2) 3D Printer Controller RAMPS 1.4 It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion. (3) A4988 Stepper Motor Driver A4988 is a complete micro-stepping motor driver with built-in translator for easy operation (4) LCD 12864 Graphic Smart Display Controller This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included. Package List: (1) RAMPS 1.4 x 1 (2) Mega 2560 R3 x 1 (3) A4988 Stepper Motor Driver with Heatsink x 5 (4) LCD 12864 Graphic Smart Display Controller x 1 (5) Smart Adapter x 1 (6) Cable x 2 (7) USB Cable x 1

Product Features

  • 3D Printer Controller Kit Mega 2560
  • 3D Printer Controller RAMPS 1.4,A4988 Stepper Motor Driver
  • LCD 12864 Graphic Smart Display Controller
  • 3D Printer Controller 100% compatible with Arduino RepRap
  • Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents

Click Here For More Information

3DSWAY 3D Printer Board 32 bit Controller STM32F4 Lerdge Board with Thermistor DRV8825 Motor Drive Support WiFi Auto-leveling Big size printer

The Lerdge board with 3.5-inch full-color touch screen, is a new and good choice as a 32bit 3D printer motherboard. Lerdge is compatible with various slice software, and supports multiple 3D printer models (including XYZ/Corexy/Delta,etc. and later on the SLA and SLS models).

● Lerdge supports a variety of printing methods, including wired-line (USB) / WIFI wireless / U disk / TF card / card reader printing.
● The motherboard also supports real-time pause while printing and supports the breakpoint printing.
● 3DTouch, BLTouch, film pressure probe and some others leveling sensors are supported.
● Functions of RGB lighting control and model surface optimization are added to the motherboard.
● Customizations are available and welcome, including the multiple languages, personalized UI, software development, etc.

Dimensions: 90*90mm
Microprocessor: STM32F4
Input voltage: 8V~35V 10~15A
Power Interface: ATX High Current Dual Interface
Motor drive supported: A4988, DRV8825, LV8729 and TMC2100
Motor driver interface: Single-head is 4-channel and 16-segment (scalable)
Temperature Sensor Interface: two 100K NTC (RTD), and one MAX6675 (thermocouple)
Supported file formats: G-code
Recommended software: Cura / Pronterface / Repetier-Host / Makerware / Simplify3d
Firmware Update: Support TF card and U disk update

Shipping list:
Lerdge motherboard (Thermistor) with DRV8825 Driver * 1set
3.5″ Touch Screen * 1pc
30cm FCC cable *1 pc
30cm power cable * 1pc
Jumper cap and terminal reed * 1set

Please don’t hesitate to contact us if you have any question about the Lerdge boards.

Product Features

  • Lerdge supports a variety of printing methods
  • The temperature measurement methods can be switched freely between thermistors and thermocouples
  • Supports for high-temperature print head
  • More modules will be available for the Lerdge board

Visit The Website For More Information…

Orion Motor Tech PLA 3D Printer Filament 1.75mm Diameter 1kg 2.2lbs (white)

Our Thermoplastic 3D Filaments are made from the best materials available and have been thoroughly tested for the best possible results. PLA materials are extruded with great precision, which means better looking prints, less calibration and fewer extruder failures. The materials will work flawlessly with most 3D extruders currently in the market.

Specification:
Material: PLA
Density 1.25g ± 0.05g/cm³
Melting Point: 180℃ (356°F)
Tensile Strength: ≥60MPa
Bending Strength: ≥60MPa
Notch Impack Strength: 4.53 lbs / ft2
Distortion Temperature: 60℃(140°F)
Printing Temperature: 190°C – 220°C (374°F – 428°F )

Product Features

  • Made of PLA (Polylactic Acid) material of premium quality, no kinks or breaks
  • Work flawlessly with most 3D extruders/printers currently in the market
  • Recommended printing temperature is 190°C – 220°C (374°F – 428°F )
  • Superior materials ensure better looking prints, less calibration & fewer extruder failures

Click Here For More Information

Wangdd22 3D Printer kit RAMPS 1.4 Control Panel Printer Control Reprap MendelPrusa +5 pcs A4988 StepStick Stepper Motor Driver Module with Heatsink for 3D Printer.

Using This suite (1pcs RAMPS 1.4 Control Panel Printer Control Reprap MendelPrusa +5 pcs A4988 Driver Module with Heatsink) on your Arduino-compatible MEGA shield for easy service,part replacement,upgrade-ability and expansion.

A4988:
Simple step and direction control interface.
Can interface directly with 3.3 V and 5 V systems.
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout.
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates.
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
45 V maximum supply voltage.
Built-in regulator.(no external logic voltage supply needed)

RAMPS 1.4 Controller:
Expandable to control other accessories.
3 Mosfets for heater / fan outputs and 3 thermistor circuits.
Fused at 5A for additional safety and component protection
Heated bed control with additional 11A fuse.
Fits 5 Pololu stepper driver boards.
Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
I2C and SPI pins left available for future expansion.
All the Mosfets are hooked into PWM pins for versatility.
Servo style connectors are used to connect to the end stops, motors, and LEDs. These connectors are rated for 3A, very compact, and globally available.
SD Card add on available.
LEDs indicate when heater outputs on.
Option to connect 2 motors to Z for Prusa Mendel.

Tips:
When inserting the A4988 module,make sure the direction is right.

Package include:
1 x RAMPS 1.4 Controller Board
5 x A4988 Stepstick Driver with Heat Sink

Product Features

  • RAMPS 1.4 expansion board as a driver expansion board, can be used for engraving machines, 3D printers.and It is a total of five slots, can drive five A4988 stepper motor.
  • Stepper motor wiring as follows: 2A, 2B is a group (red, green), 1A, 1B is a group (blue, yellow), if want to change direction, can be change the position of one group , for example 2A, 2B mutually exchanged.
  • Flexible set: 1pcs RAMPS 1.4 Controller Board+ 5pcs A4988 Stepstick Stepper Motor Driver Module with Heat Sink on your Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • Each road stepper motors only need two IO ports.
  • Step five selectable modes: full , 1/ 2, 1 / 4, 1 / 8 and 1/ 16

Click Here If You Need More Detailed Info…