HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…

Arduino 3D Printer Controller Kit – Mega 2560 Board, 3D Printer Controller RAMPS 1.4 Board, 5 Steppers, SD Card Slot, 12V, 180W

Build your own 3D printer controller kit and print all your 3D designs via G-codes on your SD card without the need of a PC.

Manufacturer SpecificationsManufacturer_Specifications
GeneralgeneralMax power supply for these ramps: 12VMax watts for these ramps: 180WMax watts for the hotbed: 100WMax temperature for the hotbed: 50 Degree CelsiusThis kit consists of a RAMPS 1.4 shield, an Mega 2560 board, five Stepper drivers and a LCD.It can control up to 5 stepper motors with 1/16 stepping precision and interface with a hotend, a heatbed, a fan (or a second hotend), a LCD controller, a 12V (or 24V with appropriate modification) power supply, up to three thermistors, and up to six end stoppers.RAMPS 1.4 shield is a popular control board for RepRap Prusa i3 3D compatible printer.A4988 Stepper Motor Driver is built-in translator for easy operationLCD 12864 with Controller contains an SD-Card reader, a rotary encoder and a 128 Character x 64 Line LCD display.
Dimensionsdimension_infoArduino Board Dimensions: 115x 50x 9mm (L x W x D)Arduino Board Weight: 35g3D Printer Controller Board Dimensions: 105x 60x 20mm (L x W x D)3D Printer Controller Board Weight: 68gWeight/dimension is for the main item of this boxed product, to help you compare product sizes before buying: please do not base your shipping calculations on this price – shipping prices depend on your cart contents, shipping destination, and shipping method: please use the checkout to select options and preview shipping price for your total order.
Product NotesProduct_NotesDo not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can remove static charge by touch

Click Here If You Need More Detailed Info…

[Sintron] 3d Printer Kit , Ramps 1.4 + Mega 2560 + 5pcs A4988 Stepper Driver w/ Heatsink + LCD 12864 Smart Controller + 3 Pcs End Stop + Mk2b Heat Bed + 2 Pcs Pulley + 2m Gt2 Belts for Reprap Prusa i3

Overview:

This kit is a good start for starter to build your own 3D printer. basically once you get the electronic parts done. then later it would be more easier to complete the rest parts.and yes, this is almost all the electronics you need for your 3D Printer.(except motors and extruder hotend)
If you are not sure what you need to complete your 3d printer project, please feel free to ask. We not just sell them, we also provide professional after-sales service, We will offer you a detailed tutorials including project introduction and their source codes. so welcome to discuss with us, we will try to do technical support as much as we can.

(1)3D Printer Controller RAMPS 1.4 – You can check:https://www.amazon.com/dp/B06WP5DDP1

(2)Mega 2560 R3 – You can check:https://www.amazon.com/dp/B00E94CGTQ

(3)LCD 12864 Graphic Smart Display Controller – You can check:https://www.amazon.com/dp/B00L72FAZU

(4)A4988 Stepper Motor Driver with Heatsink – You can check:https://www.amazon.com/dp/B00JXGT1G6

(5)Mechanical Endstop Switch – You can check: https://www.amazon.com/dp/B00OCFEZ1O

(6)2M GT2 Belt + 2 pcs GT2 20 Tooth Pulleys – You can check: https://www.amazon.com/dp/B00OFUZSP8

(7)MK28 Heatbed:This is the latest version of MK2B,100% compatible with all Prusa and Mendel 3d printer variants.

Package List:

(1)3D Printer Controller RAMPS 1.4 x1
(2)Mega 2560 R3+USB Cable x1
(3)A4988 Stepper Motor Driver with Heatsink x5
(4)LCD 12864 Smart Controller x1
(5)MK28 Heatbed with Thermistor and High Temp Wire x1
(6)Mechanical Endstops x3
(7)2M GT2 Belt+20 Tooth Pulleys x2
(8)Smart Adapter x1
(9)30cm Cable x2
(10)Storage Box x1

Product Features

  • (1) 3D Printer Controller RAMPS 1.4 x 1 + Mechanical Endstops x 3
  • (2) Arduino-Compatible Mega 2560 R3 With USB Cable x 1
  • (3) A4988 Stepper Motor Driver With Heatsink x 5
  • (4) LCD 12864 Graphic Smart Display Controller Kit x 1
  • (5) MK28 Heated Bed with Thermistor and High Temp Wire x 1

Click Here If You Need More Detailed Info…

Longruner 3d Printer Controller Kit Mega 2560 R3 + Ramps 1.4 + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display Controller with Adapter for Arduino Reprap

Update High Quality Ramp Board by changing MOSFET: Old MOSFET IC Model : PDF55N06 Specification:VDSS:60V ID:55A New MOSFET IC model: HM60N06 Specification:VDSS:60V ID:60A HM60N06 current up to 60A, More safety Package List: (1) RAMPS 1.4 x 1 (2) Kuman Mega 2560 R3 x 1 (3) A4988 Stepper Motor Driver with Heatsink x 5 (4) LCD 12864 Graphic Smart Display Controller x 1 (5) Smart Adapter x 1 (6) Cable x 2 (7) USB Cable x 1

Product Features

  • 2017 Updated Version 3D Printer Controller RAMPS 1.4 It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • Mega 2560 compatible with arduino.
  • LCD 12864 Graphic Smart Display Controller This full graphic Smart Controller contains a SD-Card.
  • A4988 Stepper Motor Driver A4988 is a complete microstepping motor driver with built-in translator for easy operation.
  • Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents.

Click Here If You Need More Detailed Info…

Quimat 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits +RAMPS 1.4 + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap

Package Content: (1) Mega 2560 (2) 3D Printer Controller RAMPS 1.4 It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion. (3) A4988 Stepper Motor Driver A4988 is a complete micro-stepping motor driver with built-in translator for easy operation (4) LCD 12864 Graphic Smart Display Controller This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included. Package List: (1) RAMPS 1.4 x 1 (2) Mega 2560 R3 x 1 (3) A4988 Stepper Motor Driver with Heatsink x 5 (4) LCD 12864 Graphic Smart Display Controller x 1 (5) Smart Adapter x 1 (6) Cable x 2 (7) USB Cable x 1

Product Features

  • 3D Printer Controller Kit Mega 2560
  • 3D Printer Controller RAMPS 1.4,A4988 Stepper Motor Driver
  • LCD 12864 Graphic Smart Display Controller
  • 3D Printer Controller 100% compatible with Arduino RepRap
  • Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents

Click Here For More Information

Elegoo Mega 2560 Project The Most Complete Ultimate Starter Kit w/ TUTORIAL, MEGA 2560 controller board, LCD1602, Servo, Stepper Motor for Arduino Mega2560 UNO Nano

Elegoo Inc. is a professional manufacturer and exporter that is concerned with the design, development production and marketing of arduino, 3d printers, raspberry pi and STM32.
Our Dream is to make the best price and best quality produce for customers.
So we would like to receive your valuable suggestions for our products and we can improve them for you.

Component listing:
25pcs LED ( white,yellow,blue,red,green)
1pcs RGB LED
10pcs Ceramic Capacitor(22pf & 104pf)
2pcs Photoresistor
1pcs Thermistor
5pcs Diode Rectifier (1N4007)
4pcs Electrolytic Capacitor (10UF 50V & 100UF 50V)
10pcs NPN Transistor (PN2222 & S8050 )
1pcs Tilt Switch
5pcs Button (small)
1pcs 1 digit 7-segment Display
1pcs 4 digit 7-segment Display
1pcs Sound Sensor Module
1pcs LCD1602 Module ( with pin header)
1pcs IC L293D
1pcs IC 74HC595
1pcs Active Buzzer
1pcs Passive Buzzer
1pcs RTC Module
1pcs DHT11 Temperature and Humidity Module
2pcs Potentiometer
1pcs Rotary Encoder Module
1pcs Joystick Module
1pcs Keypad Module
1pcs 5V Relay
1pcs IR Receiver Module
1pcs MEGA2560 Controller Board
1pcs Breadboard
1pcs Servo Motor (SG90)
1pcs Stepper Motor
1pcs ULN2003 Stepper Motor Driver Board
1pcs Prototype Expansion
1pcs Power Supply Module
1pcs HC-SR501 PIR Motion Sensor
1pcs Ultrasonic Sensor
1pcs ADXL335(GY-61) Module ( with pin header)
1pcs 3V Servo Motor
1pcs MAX7219 Module
1pcs Remote
1pcs 9V 1A Power Supply
1pcs 65 Jumper Wire
1pcs Water Lever Sensor
1pcs USB Cable
1pcs 9V Battery with DC
1pcs RC522 RFID Module
100pcs Resistor (10R/100R/220R/330R/1K/2K/5K1/10K/100K/1M)
20pcs Female-to-male Dupont Wire

Product Features

  • The MEGA2560 complete starter kit with more than 200pcs components.
  • Free PDF tutorial in the CD (more than 35 lessons).
  • LCD1602 module and GY-61 sensor module with pin header ( no need to solder by yourself)
  • Nice package with clear listing and surprise including a nice small box to keep the widget such as LED , IC , buttons , diodes ,etc.
  • We have always cared about the customer experience and improve the product function details.

Click Here If You Need More Detailed Info…

LeaningTech 3D Printer Kit Mega 2560 + RAMPS 1.4 + 5X A4988 for Arduino RepRap

Description:
Mega2560 board is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator. With the bootloader, download the program directly via USB without having to go through other external writer. Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery.
Arduino development IDE interface is based on open-source principles, allows you to free download for use in project work, school teaching, motor control, interactive works.

Features:

– Microcontroller : ATmega2560
– Operating Voltage : 5V
– Input Voltage (recommended) : 7-12V
– Input Voltage (limits) : 6-20V
– Digital I / O Pins : 54 (of which 14 provide PWM output)
– Analog Input Pins : 16
– DC Current per I / O Pin : 40 mA
– DC Current for 3.3V Pin : 50 mA
– Flash Memory : 256 KB of which 4 KB used by bootloader
– SRAM : 8 KB
– EEPROM : 4 KB
– Clock Speed : 16MHz

Packing list:

– 1x Mega2560 with usb cable
– 1x Ramps 1.4 board
– 5x A4988 motor driver

Product Features

  • Mega2560 board is an ATmega2560 as core microcontroller development board
  • RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion.
  • It is designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Easy to DIY your own 3D printer: Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs; I2C and SPI pins left available for future expansion.
  • SD Card add on available,

Click Here If You Need More Detailed Info…