INKBIRD 12″ Stainless Probe NTC-30CM Sensor Thermocouple w/ DC Cord for ITC-1000,ITC-306T, ITC-308S, ITC-310T Thermostat Temperature Controller


Features:
NTC Temperature Sensor 12in Stainless Stell Probe with 6.5ft DC cord
This temperature probe can be submersed into your beer direclty during fermentation.
No need to worry about inserting a smaller probe into a separate thermowell temperature probe.
It’s ONLY compatible with INKBIRD’s following controllers: ITC-308,ITC-306T,ITC-310T, ITC-1000.

Measuring temperature range: -50℃~120℃
Sensor Type: NTC
Probe Material:Stainless steel
Probe Dimensions: 6mm x 300mm (0.24in x 12in)
Cord Length (excluding probe): 2m (6.5ft)

Package Included:
1 x 12″ Probe Sensor
1 x 10cm DC Cord cable

Product Features

  • NTC Temperature Sensor 12in Stainless Stell Probe with 6.5ft DC cord
  • It’s ONLY compatible with INKBIRD’s following controllers: ITC-308,ITC-306T,ITC-310T, ITC-1000.
  • The sensor is waterproof and is better for the freshwater tank than the saltwater tank.
  • Can be submersed into your beer direclty during fermentation.
  • Easy to use

Detailed Information available on our Homepage…

KINGPRINT 3D Printer Controller Board MKS TFT32 3.2-Inch Full-Color Touch Screen for 3D Printer

Specification:

Weight: 91g 1. Support for power continued to fight, to save power. 2. Support blanking detection. 3. The boot logo and all buttons can design their own interfaces. 4. Increase the custom function button. 5. Support full English interface. Package Included:

1 * MKS-TFT32

Product Features

  • 3.2 inch color touch screen, support U disk and SD card.
  • Reserved Wifi interfaces, increasing Wifi interface board supports Wifi.
  • To provide continuous software upgrades, easy to upgrade.
  • Can be used on creating customer base launched MKS series motherboard.
  • The master program without modification, plug and play, support Marlin, Repetier, Smoothieware firmware.

Visit The Website For More Information…

HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…

3D Printer Engraving Expansion Board Kit Controller CNC Shield V4+Nano 3.0 Board+A4988 Driver with USB Cable for Arduino

Why this kit?

CNC Shield V4+Nano 3.0 Board+A4988 Driver as a driver expansion board, can be used for engraving machines, 3D printer, and It is a total of three slots, can drive three A4988 stepper motor.

Specifications:

V4 Board Size: 7.2 x 5.9cm / 2.83 x 2.32″

Improved Nano Board Size: 4.3 x 1.8cm / 1.69 x 0.7″

Driver Size: 2 x 1.5cm / 0.78 x 0.59″

Heat Sink Size: 0.8 x 0.8cm / 0.31 x 0.31″

Package:

1 x CNC Shield V4.0

1 x Nano 3.0 Board

3 x A4988 Drivers

1 x USB Cable

3 x Heat Sinks

 

Note:

 WE DO NOT PROVIDE ANY TECHNICAL HELP. Thank you for your understanding.

Product Features

  • - It is a flexible set, with 3 axis stepper motor driver, compatible with Arduino and most shields designed for the Arduino micro-drive laser engraving machine, three-axis CNC engraving machine
  • - Power DC5V interface and 7.5-12V voltage input, compatible with GRBL for easy service, part replacement, upgrade-ability and expansion
  • - Easy to operate: 2A can be controlled within the two-phase four-wire stepper motor, simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started
  • - Released the digital IO interface and the I2C interface, easy to connect to other modules, such as ENDSTOP, LCD I2C or other I2C module
  • - Simple step and direction control interface, taking anti-static measures before you use the A4988 modules in case of short-circuit

Visit The Website For More Information…

SainSmart Ramps 1.4 + A4988 + MK2B + Mega2560 R3 + LCD 12864 3D Printer Controller Kit for 3D Printers RepRap

This is the new SainSmart 3D Printer Starter Kit, developed specially for those beginners who are interested in 3D printer. You will have a complete set of Sainsmart’s most common and useful electronic components. You may learn about Sainsmart through using these basic projects.

Sainsmart RAMPS 1.4 is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. This board is mostly based on Adrian’s Pololu_Electronics and work by Tonok. Copper etch resists methods suggested by Vik. Also inspired by Vik’s work with EasyDrivers. circuit design based mostly on Adrian’s Pololu_Electronics Joaz at RepRapSource.com supplied initial pin definitions and many design improvements. Much inspiration, suggestions, and ideas from Prusajr, Kliment, Maxbots, Rick, and many others in the RepRap community.

Package List:

1 x RAMPS 1.4
1 x Mega 2560 R3
5 x A4988 driver
1 x LCD 12864 With Controller
1 x SD card breakout For ramps
1 x Cooler Fan for 3D ramps
6 x Mechanical Endstop with cable
1 x RAMPS 1.4 wiring cable
1 x Heatbed MK2B
5 x NEMA 17 Stepper Motors
1 x USB Cable

Note:
Download the doumentation & codes here:
https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/3d+12864/arduino-0023.rar
https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-011-962/3D.rar

Product Features

  • Sainsmart Mega2560 R3 is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator.
  • Sainsmart A4988 driver is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil.
  • Sainsmart LCD 12864 contains a SD-Card reader, an rotary encoder and a 128 Character x 64 Line LCD display.
  • SainSmart Mechanical Endstop perfect for any 3D printer. 100% compatible with all Prusa and Mendel 3d printer variants.

Click Here If You Need More Detailed Info…

[Sintron] NEW Ultimate 3D Printer Full Complete Kit TW-101 2017 Upgrade Pro & Easy 3D Printer Reprap Prusa i3 + MK8 Extruder, Stepper Motor and LCD Controller

The operating principle of 3D printer is to establish a 3D model by your computer, and use slicing software system to do the slicing work for the 3D model then save to the SD card for ready to print. Made of high quality acrylic material + Steel rod (threaded & smooth), this 3D printer has a simple structure, light and portable, beautiful and trendy.

Sintoron TW-101 3D Printer Assembly Guide Video, please click this link : https://www.youtube.com/watch?v=Cjv6HPep_dU

TW-101 has complete pdf instruction as well as Exploded view video–> hardware parts
TW-101 has open source preconfigured Marlin configuration –> firmware part
We also provide software for TW-101: such as Pronterface, Slic3r. and most importantly, we can provide the configuration file of slic3r, which we spent so much time to set it up. with this, your printing would be beautiful! –> software part

Quick & Easy assembling, all you need are just one wrench + screw driver. and they are included! we have classified the parts, screws, nuts for you. this would save you lots of time!

Actually we have own this products for over one year, but we just started to sell it now. because we hope to went through all the details, and make sure all the components we selected are really useful, so customer can save time on worrying if it’s the hardware problem and focus on project only.

Therefore, if you meet any problems (I am sure you will meet dozens of problems and questions during the building process, and it’s normal), you can always contact us for technical support, because almost all the problems you will meet, we already met before, you are not just buying this product, you also get our experienced support for you. if there’s some one you can ask, you will save a lot of time.

Package list and TW101 Specifications : please check the main picture for list.

Product Features

  • (1) We don’t adapt wade extruder, we upgrade the J-head to all metal Sintron MK8 extruder (not all the MK8 extruders are the same). If you use wade extruder etc, every time when you change the filament, you have to take them apart and calibrate it all again. it takes hours sometimes. it takes you only within 1 minute to change the filament. Sintron MK8 extruder’s special design also ensure you a pleasant & smoth printing.
  • (2) We use SINTRON well-designed standard MK8 extruder, high quality stepper motor and direct drive extrusion wheel, more accurate, quick heating and fluent injection, we have made necessary design to prevent “jammed” problem. Exclusive Anti-Backlash design for Z axis , this makes the movement very quiet and stable. only Sintron got this design in the Market now! Sintron TW-101 uses 304 stainless T8 Lead Screw with Thread pitch 2mm. this makes TW-101 more accurate in printing.
  • (3) Wiring has never been as easier as TW-101. you are not a expert of electronics? Never Mind! we have mistake-proof plugs. this is also one of our special design. as long as you can read and check the color, you can do it! Further more, we have made wires with corresponding suitable length for each plug(others don’t). so it would look tight and clean! no extra mess.
  • (4) Energy Saver! TW-101 consumes only 1/3 energy of ordinary 3d printer, TW-101 adapts special tape. so you don’t need to heat the bed, therefore no worries about fire accident. but on the other hand, TW-101 by default won’t suit for ABS(toxic) printing, PLA(non-toxic) and others are preferred. it’s also a trend to use only PLA as it’s enviormental friendly and no harm for human body.
  • (5) Sintron TW-101 provide good Full tech support for the machine, unlike other sellers, just sell and know nothing about the product. we provide support for hardware, firmware & software if you would like to discuss with us! this would make sure you learn a lot from it too!

Click Here If You Need More Detailed Info…

MatterHackers Ultimachine RAMBo 1.3 3D Printer Controller Kit

This pre-assembled mother board meets all your needs – you will receive all electronic components securely soldered to the PCB, endstop wires and switches of your choice, and pre-crimped wires…plus much more!

Product Features

  • This pre-assembled mother board meets all your needs
  • You will receive all electronic components securely soldered to the PCB
  • Endstop wires and switches of your choice, and pre-crimped wires…plus much more!
  • This RAMBo 1.3 Kit is complete and is made by Ultimachine

Click Here If You Need More Detailed Info…