HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…

Wangdd22 3D Printer Parts 100Kohm NTC3950 Thermistors with Cable for 3D Printer Reprap Mend RAMPS 1.4 A4988 MK2B Heatbed(Pack of 10)

Specifications:

Negative temperature coefficient (NTC) thermistor
R @ 25: K100K-1%B25 / 50: K3950-1%
Element: thermistor type MJB2

Characteristics:

Resistance value: R (25 ° C) = 100K ± 1%
Resistance tolerance:± 1%
B value R25/50:3950k
Operating temperature range:-40° C ~+ 300 ° C
Temperature coefficient of resistance:-2 ~ -5% ° C
Maximum rated power:45mW
Dissipation power coefficient:>5mW/° C
Thermal time constant:≤7S

Colour:Milky white
Line length:1m

Package Includes:
10Pcs 100K temperature sensor

Product Features

  • High sensitivity and quick response;
  • Compact structure, easy installation;
  • Wide temperature range, good stability, high reliability;
  • Teflon wire is twice thicker than other similar products in the market. It is not easy to be break off;
  • It adopts white high temperature Teflon wire, resistant to high temperatureof 200 degrees;

Visit The Website For More Information…

SainSmart Ramps 1.4 + A4988 + MK2B + Mega2560 R3 + LCD 12864 3D Printer Controller Kit for 3D Printers RepRap

This is the new SainSmart 3D Printer Starter Kit, developed specially for those beginners who are interested in 3D printer. You will have a complete set of Sainsmart’s most common and useful electronic components. You may learn about Sainsmart through using these basic projects.

Sainsmart RAMPS 1.4 is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. This board is mostly based on Adrian’s Pololu_Electronics and work by Tonok. Copper etch resists methods suggested by Vik. Also inspired by Vik’s work with EasyDrivers. circuit design based mostly on Adrian’s Pololu_Electronics Joaz at RepRapSource.com supplied initial pin definitions and many design improvements. Much inspiration, suggestions, and ideas from Prusajr, Kliment, Maxbots, Rick, and many others in the RepRap community.

Package List:

1 x RAMPS 1.4
1 x Mega 2560 R3
5 x A4988 driver
1 x LCD 12864 With Controller
1 x SD card breakout For ramps
1 x Cooler Fan for 3D ramps
6 x Mechanical Endstop with cable
1 x RAMPS 1.4 wiring cable
1 x Heatbed MK2B
5 x NEMA 17 Stepper Motors
1 x USB Cable

Note:
Download the doumentation & codes here:
https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/3d+12864/arduino-0023.rar
https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-011-962/3D.rar

Product Features

  • Sainsmart Mega2560 R3 is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator.
  • Sainsmart A4988 driver is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil.
  • Sainsmart LCD 12864 contains a SD-Card reader, an rotary encoder and a 128 Character x 64 Line LCD display.
  • SainSmart Mechanical Endstop perfect for any 3D printer. 100% compatible with all Prusa and Mendel 3d printer variants.

Click Here If You Need More Detailed Info…

Aluoflower Anet LCD 2004 LCD Blue Display Screen Controller Module for RAMPS 1.4 3D Printer Parts


Description:

Features:
100% brand new and high quality.
The large screen LCD display type: 4 lines 20 characters in each.
Comes with encoder, can realize parameter adjustment, choose print and file.
Plug and play, but need to modify the firmware.

Specifications:
Item Type: Anet LCD2004 LCD Display Blue Screen Controller
Model: Control Screen A2004
Color: Red+Green (shown as pictures)
Size: 16×6.5×1.5cm/6.30×2.56×0.59in (Approx.)
Quantity: 1PC (other accessories in the picture is not included)

Note:
1.Transition: 1cm=10mm=0.39inch
2.Please allow 0-1cm error due to manual measurement. pls make sure you do not mind before you bid.
3.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!

Package includes:
1 X Anet LCD2004 LCD Display Blue Screen Controller

Product Features

  • 100% brand new and high quality.
  • Plug and play, but need to modify the firmware.
  • Size: 16×6.5×1.5cm/6.30×2.56×0.59in (Approx.)
  • The large screen LCD display type: 4 lines 20 characters in each.
  • Comes with encoder, can realize parameter adjustment, choose print and file.

Visit The Website For More Information…

Arduino 3D Printer Controller Kit – Mega 2560 Board, 3D Printer Controller RAMPS 1.4 Board, 5 Steppers, SD Card Slot, 12V, 180W

Build your own 3D printer controller kit and print all your 3D designs via G-codes on your SD card without the need of a PC.

Manufacturer SpecificationsManufacturer_Specifications
GeneralgeneralMax power supply for these ramps: 12VMax watts for these ramps: 180WMax watts for the hotbed: 100WMax temperature for the hotbed: 50 Degree CelsiusThis kit consists of a RAMPS 1.4 shield, an Mega 2560 board, five Stepper drivers and a LCD.It can control up to 5 stepper motors with 1/16 stepping precision and interface with a hotend, a heatbed, a fan (or a second hotend), a LCD controller, a 12V (or 24V with appropriate modification) power supply, up to three thermistors, and up to six end stoppers.RAMPS 1.4 shield is a popular control board for RepRap Prusa i3 3D compatible printer.A4988 Stepper Motor Driver is built-in translator for easy operationLCD 12864 with Controller contains an SD-Card reader, a rotary encoder and a 128 Character x 64 Line LCD display.
Dimensionsdimension_infoArduino Board Dimensions: 115x 50x 9mm (L x W x D)Arduino Board Weight: 35g3D Printer Controller Board Dimensions: 105x 60x 20mm (L x W x D)3D Printer Controller Board Weight: 68gWeight/dimension is for the main item of this boxed product, to help you compare product sizes before buying: please do not base your shipping calculations on this price – shipping prices depend on your cart contents, shipping destination, and shipping method: please use the checkout to select options and preview shipping price for your total order.
Product NotesProduct_NotesDo not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can remove static charge by touch

Click Here If You Need More Detailed Info…

Anet 12864 LCD Smart Display Screen Controller Module with Cable for RAMPS 1.4 Arduino Mega Pololu Shield Arduino Reprap 3D Printer Kit Accessory

Features:
12864 LCD smart controller for 3D printer.
Supports for RAMPS 1.4 control board.
Built-in encoder allows you adjusting the parameter and selecting file to print.
Large size screen, clear white characters with blue backlit.
Tuning and press the round button to control, with buzzer for reminding, a reset button, easy for operation.

Specifications:
Brand: Anet
Model: 12864
Screen: LCD
Screen Size: 3in
Item Weight: 139g / 4.9oz
Package Size: 18 * 10 * 3cm / 7.1 * 3.9 * 1.2in
Package Weight: 143g / 5.0oz

Package List:
1 * 2004 LCD Screen
2 * Cable

Product Features

  • 12864 LCD smart controller for 3D printer.
  • Supports for RAMPS 1.4 control board.
  • Built-in encoder allows you adjusting the parameter and selecting file to print.
  • Large size screen, clear white characters with blue backlit.
  • Tuning and press the round button to control, with buzzer for reminding, a reset button, easy for operation.

Click Here If You Need More Detailed Info…

[Sintron] 3d Printer Kit , Ramps 1.4 + Mega 2560 + 5pcs A4988 Stepper Driver w/ Heatsink + LCD 12864 Smart Controller + 3 Pcs End Stop + Mk2b Heat Bed + 2 Pcs Pulley + 2m Gt2 Belts for Reprap Prusa i3

Overview:

This kit is a good start for starter to build your own 3D printer. basically once you get the electronic parts done. then later it would be more easier to complete the rest parts.and yes, this is almost all the electronics you need for your 3D Printer.(except motors and extruder hotend)
If you are not sure what you need to complete your 3d printer project, please feel free to ask. We not just sell them, we also provide professional after-sales service, We will offer you a detailed tutorials including project introduction and their source codes. so welcome to discuss with us, we will try to do technical support as much as we can.

(1)3D Printer Controller RAMPS 1.4 – You can check:https://www.amazon.com/dp/B06WP5DDP1

(2)Mega 2560 R3 – You can check:https://www.amazon.com/dp/B00E94CGTQ

(3)LCD 12864 Graphic Smart Display Controller – You can check:https://www.amazon.com/dp/B00L72FAZU

(4)A4988 Stepper Motor Driver with Heatsink – You can check:https://www.amazon.com/dp/B00JXGT1G6

(5)Mechanical Endstop Switch – You can check: https://www.amazon.com/dp/B00OCFEZ1O

(6)2M GT2 Belt + 2 pcs GT2 20 Tooth Pulleys – You can check: https://www.amazon.com/dp/B00OFUZSP8

(7)MK28 Heatbed:This is the latest version of MK2B,100% compatible with all Prusa and Mendel 3d printer variants.

Package List:

(1)3D Printer Controller RAMPS 1.4 x1
(2)Mega 2560 R3+USB Cable x1
(3)A4988 Stepper Motor Driver with Heatsink x5
(4)LCD 12864 Smart Controller x1
(5)MK28 Heatbed with Thermistor and High Temp Wire x1
(6)Mechanical Endstops x3
(7)2M GT2 Belt+20 Tooth Pulleys x2
(8)Smart Adapter x1
(9)30cm Cable x2
(10)Storage Box x1

Product Features

  • (1) 3D Printer Controller RAMPS 1.4 x 1 + Mechanical Endstops x 3
  • (2) Arduino-Compatible Mega 2560 R3 With USB Cable x 1
  • (3) A4988 Stepper Motor Driver With Heatsink x 5
  • (4) LCD 12864 Graphic Smart Display Controller Kit x 1
  • (5) MK28 Heated Bed with Thermistor and High Temp Wire x 1

Click Here If You Need More Detailed Info…