xlpace Auto Self-Leveling Position Sensor Kit for Anet A8 Prusa i3 3D Printer RepRap

Functional Auto Leveling Position Sensor

Great Click Auto Leveling Position Sensor are designed for 3D Printer Accessories.

Application

Ideal Leveling Position Sensor for Anet A8 Prusa i3 3D Printer RepRap.

Specifications

Weight: 68g
Suits for: Anet A8
Wire Type: DC 3 Wire Type(Brown, Black, Blue)
Working Voltage: 10-30V DC
Current: 300mA
Sensor Size: 18x17x34mm/0.71″x0.7″x1.34″
Cable Length: 140cm / 55.1″

Package Included

1x Proximity Sensor; 1x Plate; 2x Screw

Lifetime Warranty

100% high quality and good services, your good feedback will be appreciated and encouraged us to further improve our service and product quality for your next purchase.
If any question, pls contact us, we must will provide you a good solution.

Product Features

  • ღ.Works well with Anet A8 3D printer.
  • ღ.Pretty solution for auto-adjusting heatbed level, convenient for use.
  • ღ.3D printer waterproof anti-jamming DC three-wire npn,10-30V DC working voltage.
  • ღ.Anti-jamming three-wire, 140cm / 55.1in cable length.
  • ღ.Comes with mounting plate and pre soldered connector so no wiring is needed, just unplug the original z stop and plug in sensor and screw into the back of printer.

Click Here For More Information

RONGT 3D Printer Accessories Auto Leveling Sensor P802M P802E Leveling Sensor for 3D Printer Anet A8 Prusa i3

To Fit: 3D Printer
Compatible Model: Anet A8, Anet A6, For Prusa i3
Type: Extruder Upgrade Kit
Material: Acrylic + Plastic
Suitable for: Accessory
Product weight: 0.0620 kg
Product size: 8.00 x 7.00 x 2.20 cm / 3.15 x 2.76 x 0.87 inches
Package Contents: 1 x Auto Leveling Sensor ( 150cm Line )

Product Features

  • Detection range: 8mm
  • Working voltage: DC 6 – 36V
  • It is an auto leveling sensor for 3D printers. It can precisely measure the tilt of your print surface.
  • It can greatly improve the printing precision of your 3D printer.
  • For Anet A8 or other 3D printer which has the software of the automatic leveling control system.

Detailed Information available on our Homepage…

INKBIRD 12″ Stainless Probe NTC-30CM Sensor Thermocouple w/ DC Cord for ITC-1000,ITC-306T, ITC-308S, ITC-310T Thermostat Temperature Controller


Features:
NTC Temperature Sensor 12in Stainless Stell Probe with 6.5ft DC cord
This temperature probe can be submersed into your beer direclty during fermentation.
No need to worry about inserting a smaller probe into a separate thermowell temperature probe.
It’s ONLY compatible with INKBIRD’s following controllers: ITC-308,ITC-306T,ITC-310T, ITC-1000.

Measuring temperature range: -50℃~120℃
Sensor Type: NTC
Probe Material:Stainless steel
Probe Dimensions: 6mm x 300mm (0.24in x 12in)
Cord Length (excluding probe): 2m (6.5ft)

Package Included:
1 x 12″ Probe Sensor
1 x 10cm DC Cord cable

Product Features

  • NTC Temperature Sensor 12in Stainless Stell Probe with 6.5ft DC cord
  • It’s ONLY compatible with INKBIRD’s following controllers: ITC-308,ITC-306T,ITC-310T, ITC-1000.
  • The sensor is waterproof and is better for the freshwater tank than the saltwater tank.
  • Can be submersed into your beer direclty during fermentation.
  • Easy to use

Detailed Information available on our Homepage…

Jili Online 3D Printer Part Material Detection Module with Wire for 1.75mm Filament Module Monitor Sensor

Description:

– Wear-resistant copper sets added in both the inlet and outlet to effectively extend the product life. Wiring: Connect the module to the M-sensor port on the motherboard.
– Used for Lerdge board: When there is material in, the green light in the module keeps lighting. when the material is exhausted, the green light goes off,and the motherboard executes the pause command operation, after the replacement of the material, can continue to print.
– Used with other motherboards: The material detection module uses the level transition detection method.
– When with material in, the detection level signal should be high, and when no material, the material port level signal goes low.
– When the system detects a determined transition from high to low level, it will regard it as the material exhausted, then the board executes the pause command operation, and after the replacement of the material, it will continue to print.

Specification:

– Board size: 38*30*13mm/1.50*1.18*0.51inch

Package Includes:

1 Piece Material detection module with cable.

Product Features

  • Wear-resistant copper sets added in both the inlet and outlet to effectively extend the product life. Wiring: Connect the module to the M-sensor port on the motherboard.
  • Used for Lerdge board: When there is material in, the green light in the module keeps lighting. when the material is exhausted, the green light goes off,and the motherboard executes the pause command operation, after the replacement of the material, can continue to print.
  • Used with other motherboards: The material detection module uses the level transition detection method.
  • When with material in, the detection level signal should be high, and when no material, the material port level signal goes low.
  • When the system detects a determined transition from high to low level, it will regard it as the material exhausted, then the board executes the pause command operation, and after the replacement of the material, it will continue to print.

Visit The Website For More Information…

Jili Online 3D Printer Part Material Detection Module with Wire for 1.75mm Filament Module Monitor Sensor

Description:

– Wear-resistant copper sets added in both the inlet and outlet to effectively extend the product life. Wiring: Connect the module to the M-sensor port on the motherboard.
– Used for Lerdge board: When there is material in, the green light in the module keeps lighting. when the material is exhausted, the green light goes off,and the motherboard executes the pause command operation, after the replacement of the material, can continue to print.
– Used with other motherboards: The material detection module uses the level transition detection method.
– When with material in, the detection level signal should be high, and when no material, the material port level signal goes low.
– When the system detects a determined transition from high to low level, it will regard it as the material exhausted, then the board executes the pause command operation, and after the replacement of the material, it will continue to print.

Specification:

– Board size: 38*30*13mm/1.50*1.18*0.51inch

Package Includes:

1 Piece Material detection module with cable.

Product Features

  • Wear-resistant copper sets added in both the inlet and outlet to effectively extend the product life. Wiring: Connect the module to the M-sensor port on the motherboard.
  • Used for Lerdge board: When there is material in, the green light in the module keeps lighting. when the material is exhausted, the green light goes off,and the motherboard executes the pause command operation, after the replacement of the material, can continue to print.
  • Used with other motherboards: The material detection module uses the level transition detection method.
  • When with material in, the detection level signal should be high, and when no material, the material port level signal goes low.
  • When the system detects a determined transition from high to low level, it will regard it as the material exhausted, then the board executes the pause command operation, and after the replacement of the material, it will continue to print.

Visit The Website For More Information…

BIQU Metal Kossel Pro DIY 3D Printer Rail Guide Delta Rostock Kit Large Printing Size 250x250x380mm with BLTouch Auto Bed Leveling Sensor and TFT35 Touch Screen

Basic Specification:
Principal:FDM(Fused Deposition Modeling)
Demension:400*420*860mm
Packing Size:915*455*110mm
Net Weight:8.5kg
Shipping Weight:13.5kg
Software Specification
Operation System:Windows MacOs linux
Slice software:cura ,simplify3d ,slic3r
Input Format:STl OBJ
Output Format:G-code

Hardware Specification:
Max printing size:250*250*380mm
Printer Head:1PC
Location Accuracy:0.1mm
Layer Height:0.05-0.4mm
Nozzle Size:0.4mm
Filament Diameter:1.75mm
Control Mode :Online Printing and Offline Printing

Package List:
1xKossel 3D Printer
1xPerching Knife
1xDouble Screwdriver
1xUSB Cable
1xCombination Cut Pliers
1xPower Connector
2xConnector
1xSD Card
1xSD Card Reader
1xPrinted Fan
1x500g PLA Filament
6xM6 Nozzles
1xSet of Allen Key
1xHeated Bed Sticker
1xHeated Bed Power Module Expansion

Product Features

  • Use BLTouch, an auto leveling sensor for delta rostock 3D Printers, more simple, smart and high-precision
  • Upgrade bigtreetech TFT35 touch screen, it is more simple, convenient and natural
  • Large printing volume, 250*250*380mm, satisfy your bigger size printing needs
  • Ultra-quiet printing, use upgraded versionTMC2100 stepper motor driver and BIQU GEN V1.0 control board
  • High precision linear guide version, more precision, more stable

Click Here If You Need More Detailed Info…

Aibecy NTC 3950 100K ohm Thermistor Sensor with 1.1m Cable for RepRap Prusa i3 Anet 3D Printer Kit Replacement Parts

Features:
NTC pre-wired thermistor for most 3D printers heat bed & extruder.
100K ohm temperature sensor.
3P terminal for connecting.
With 1.1m long high temperature insulated wire.
Durable material for long life.

Specifications:
Material: High Temperature Teflon(200°C)
Resistance: at 25°C=100K ohm
Cable Length: Approx. 1.1m
Working Temperature Range: -40°C~+300°C
Package Size: 7 * 5 * 1cm / 2.8 * 2 * 0.4in
Package Weight: 8g / 0.3oz

Package List:
1 * Thermistor

Note:
The item only includes the thermistor.

Product Features

  • NTC pre-wired thermistor for most 3D printers heat bed & extruder.
  • 100K ohm temperature sensor.
  • 3P terminal for connecting.
  • With 1.1m long high temperature insulated wire.
  • Durable material for long life.

Visit The Website For More Information…